Aluminium Blue Water Cruiser Project
New Quality Fittings Included
- Barco REF# · 255601
- Eslora total · 11.58m
- Año · 2012
- Construcción · Aluminio
- Perfíl de carena · Quilla corrida
- Motor · 1 x gasoil 80cv, Perkins M90 (2015)
- Lugar · Plymouth, Devon, UK (by appointment only)
Este barco está fuera del mercado Aqui hay algunas embarcaciones que siguen en venta
Detalles suplementarios
| Proyectista | Ganley Yachts, New Zealand |
|---|---|
| Astillero | Previous Owner, Isle of Wight |
| Lugar | Plymouth, Devon, UK (by appointment only) |
| Capacidad de carburante | 176.0 G Total - 2 Tanks |
| Capacidad de agua | 132.0 G Total - 5 Tanks |
| Capacidad aguas sanitarias | 13.2 G Total - 1 Tanks |
Sistemas Mecánicos
| Motor | 1 x gasoil 80cv |
|---|---|
| Marca del motor y el modelo | Perkins M90 (2015) |
| Horas de motor |
motor1= 1 |
| Motor refrigerado por | Indirect |
| Gobierno | caña |
| Propulsión | Eje/s |
| Consumo de carburante | Desconocido |
Perkins Factory reconditioned engine £5000
New drive shaft
Batteries will be chargeable by engine & shore power
Possible to change steering from tiller to wheel - steering parts excluding wheel available.
Batteries charged by engine and shore power
Dimensiones
| Eslora total | 11.58m |
|---|---|
| Eslora de flotación | 10.06m |
| Manga | 3.35m |
| Calado mín. | 2.00m |
| Calado máx. | 2.00m |
| Desplazamiento | 11,025.0lbs |
| Altura interior | 1.91m |
| Ubicación/Lugar | A tierra |
Sistemas eléctricos
24 batería de voltios,
Construcción
| Construction | Aluminio |
|---|---|
| Perfíl de carena | Quilla corrida |
| Acabado | Aluminium acabado |
Displacement figure approximate
Hull plate is 6.5mm marine grade Aluminium
Frames are 75 x 40" L section with doublers at 900mm centres
The owner believes there is the following outstanding work to be done on this project:
'The engine installation needs to be finished including the exhaust system, fuel system and controls
The shaft seal needs to be installed with for example a Tides marine seal
The prop needs to be obtained
The Ballast needs to be fitted, washer punchings (3 tons required) and then the bilge pumps etc. can be connected (onboard ready)
Weld on the hand rails
The wiring is all there ready for connection."
Interiores
| Lavabos | 1 |
|---|---|
| Baño | 1 Baño (Manual) |
Double sink in galley
Heads fitted & plumbed with holding tank
Interiores
| Fregadero/Lavabo | |
|---|---|
| Nevera | |
| Sistema de agua bajo presión | |
| No fumadores |
Double sink in galley
Heads fitted & plumbed with holding tank
Equipo de cubierta
| Cabos |
|---|
1 anclas
(Delta 20kg)
60.00m de cadena
Equipo de seguridad
5 bombas de achique (1 manual / 4 eléctrico)
Bilge pumps need to be fitted
Comentario del broker
This sturdy partially fitted out aluminium hull has the potential to become a fantastic blue water cruising vessel, power or sail (the previous owner planned to fit out as power but this can be changed).
The unique stern was originally constructed by a previous owner to house a salvage winch for retrieving treasure in the Pacific Ocean.
A great deal of the expensive internal work has already been carried out by a professional engineer. She comes fitted with an 80hp Perkins M90 at a cost of £5k, which is fully reconditioned and unused from the Perkins factory. A new prop shaft is also fitted and she has plenty of brand new tankage fitted for fuel, water and a holding tank for waste.
The galley is partially fitted with a double sink and fridge. The heads/wet room is also a work in progress with a new toilet & sink whilst a shower still needs to be purchased & fitted.
All Tru Design skin fittings are ABYC approved & rated H-27 standard for aluminium hulls.
Also included are 4 electric bilge pumps plus 1 manual, a battery charger, fresh water pumps and chain plates if needed.
This is a great opportunity to acquire a very reasonably priced, unused, aluminium hull and to finish it to your own desired specification, power or sail.
These boat details are subject to contract.
Note: Offers on the asking price may be considered.